Pro-Fit Stainless Steel BackPlate, Medium (small and large sizes also available)
Precision Waterjet cut from heavy 11 gauge (.118” thick) 300 Series Stainless Steel. Medium size fits most divers from 5 ft. 3 in. to 6 ft. 0 in. 4.7 lbs.
DSS back plate features angled harness slots and a much flatter profile than other plates. This results in greater comfort and a lower profile when used with a single tank.
Single tank cam strap slots are located to avoid interference with harness webbing.
Large diameter holes located near the plate edge permits easy attachment of clip on accessories. This not possible with stamped plates.
All load bearing webbing slots have tough thermoplastic elastomer grommets over molded, permanently bonded to plate for zero webbing wear.
Dive Doubles? No Problem Holes and slots are provided at 11” centers for mounting Double tanks. Lower Slots allow easy mounting of doubles with bands that are not exactly at 11” centers.
All edges and holes are carefully deburred. Vibratory abrasive finished to a uniform satin surface.
Uniformly bent using one shot bending die to ensure consistent flatter profile.
Pro-Fit Hybrid Kydex / Stainless Steel BackPlate, Medium (small and large sizes also available)
DSS back plate features angled harness slots and a much flatter profile than other plates. This results in greater comfort and a lower profile when used with a single tank. Medium size fits most divers from 5 ft. 3 in. to 6 ft. 0 in.
Single tank cam strap slots are located to avoid interference with harness webbing.
Large diameter holes located near the plate edge permits easy attachment of clip on accessories. This not possible with stamped plates
Oversized 16 ga Stainless Reinforcements Rivet attached at each loaded webbing location. Oversized Stainless assures webbing bears on deburred plastic edge, not sharp Stainless.
Precision Waterjet cut from 1/8 thick Kydex,high toughness plastic alloy. Slightly flexible for improved comfort. Less than 1 lb. negative.
Kydex plate is perfect for travel diving because of it's lightness.
We package a
Hogarthian (hog) harness system with our complete modular rig; including stainless steel D-rings for attaching lights, accessories and side mounted tanks; stainless steel tri-glide keepers and buckles for durability and corrosion resistance; inflator hose release flange for easy emergency decoupling even with thick gloves; tank straps with compression blocks for secure gas supply;
free sheath and dive knife.
Torus 26, Full Circle Style Single Tank Wing W/ 22 mil bladder
No Zipper! These new wings are sewn shut. The heavy duty 22 mil urethane bladder material eliminates the need to access the bladder via a zipper. No zipper to fail, or get pinched between the tank and plate. Simple, clean clutter free wing design.
22 mil urethane RF welded inner bladder. Most wing bladders are .012 inches to .015 inches in thickness. At .022 inches (22mil) DSS bladders offer improved resistance to impact damage.
Very Narrow Design. Introduced in 2004, the DSS LCD Wings first used the extremely narrow, 3 inch wide center panel design. This contrasts with other wings available at the time that have ~ 6- 8 inch wide center panels, about the width of the tank. DSS Single tank wings use both the Back Plate and the tank to control the shape of the wing. This permits a wing with a very narrow overall profile. The Single Tank Torus Wings continue this concept.
Rugged Construction 1050 Ballistic Nylon Outer Shell, Sewn throughout with #138 Bonded Nylon thread, top stitched for extra seam strength. Using the same custom molded, sewn in elastomeric components, Single Tank Torus permit quick and easy mounting and demounting. Secure tank attachment without requiring the extra parts and cost of a Single Tank Adapter (STA) is a key feature.
One delrin OPV or Rear Dump. Mounted on the diver’s left, on the diver’s side of the wing. Equipped with a knotted pull cord.
Simple Elbow. No rapid exhaust or pull Dump on the 13 inch Inflator Hose, 18 inch Lp Hose and Lp hose release are included with every wing. Generic Power Inflator widely used in the industry, making parts and service easily available.
Building a Complete BCD Rig for your diving needs:
1. Choose backplate material-
stainless steel or
Kydex 2. Choose backplate size (based on your height) -
medium 5'3" to 6';
small less than 5'3";
large more than 6'
3. Do you dive (a)
single tank or (b)
twin tanks, then choose
wing lift (a - singles) 17 pounds; 26 pounds
(b - twins) 38 pounds; 49 pounds
4.
Send us your selections and we will configure you BC to your specs. Free professional advice and adjustment of your modular bc.
Price: Php 30,000
